Showing results: 166 - 180 of 289 items found.
-
A.H.Systems, Inc.
A.H. Systems'' Preamplifier line is an excellent choice with a rugged design, no hassles with soldering your own power leads and they improve overall system sensitivity by at least 20 dB. All of A.H. Systems'' Preamplifiers come with a 12-volt (or 15-volt) DC regulated power source. A low voltage indicator confidently allows you to power the amplifier with your own external 12-volt DC battery. This makes it a convenient choice for field measurements. See table below for amplifier specifications.
-
E5007A -
Keysight Technologies
The E5007A provides the impedance analysis (ZA) firmware for the E5061B LF-RF network analyzer. This option enables the analyzer to measure impedance parameters of electronic components such as capacitors, inductors, and resonators. The combination of NA and ZA capabilities further enhances the analyzer’s versatility as a general R&D tool. Basic ZA functionalities including fixture compensation and equivalent circuit analysis are supported by the firmware. The DC biased impedance measurement is possible with the built-in DC bias source provided by the E5061B-3L3/3L4/3L51.
-
TH1775 -
Shenzhen Chuangxin Instruments Co., Ltd.
TH1775 is a DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. High frequency LCR meter could be used, when the frequency response range is wide enough. MPU controlled auto current balance technology is adopted to realize AC+DC current overlap and constant current output from 0 to ±20A. Two TH1775 can be paralleled to supply a maximum current up to 40A.TH1775 permits high frequency measurement up to 1 MHz and can be directly controlled by TH2816A, TH2817A, TH2818 and TH2819. TH1773/TH1775 with its low additional error, wide frequency response range and sweep output function is widely used in DC biased inductance measurement. TH1775 also provides a perfect solution for magnetic material analysis.
-
Opto Diode
Opto Diode manufactures five families of infrared emitters that are used for a variety of medical and industrial applications, including gas analysis, environmental monitoring, spectroscopy, and process control. From the steady state (DC) emitters (SA Series), to high-power steady state emitters (SHA Series), to pulsable sources of black-body radiation (SVF Series) and fast pulsable sources of black-body radiation (SPF Series), to high-speed IR emitters with integrated drive electronics (PIREPLUS), we have the perfect family of products for your critical requirements.
-
67394 -
Chroma ATE Inc.
The 67394 Multi-Channel Power Module is a new generation of compact, stable and high reliability AC to DC power supply that can test the small size panels. It has multiple power sources with voltage/timing adjustable functions, protection functions and measurement circuits. Its modular design can work with FPD tester and PG card to provide standard power source for testing the panels.
-
Optomistic Products
The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
ARBS 2600 -
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
-
Bierer & Associates, Inc
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
CTPTA-504 -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.
-
WFD22 -
APPLICOS
The WFD22 is a 22 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. It combines superior dynamic performance with a very high DC accuracy.The module features fully differential inputs to reduce common-mode level disturbances. It can also be used in Single Ended mode where an internal DC-offset source sets the midscale level.
-
TWR-H Series -
IBEKO Power AB
Handheld TWR-H device is DV Power single-phase instrument designed for measuring transformer winding resistance and turns ratio.The instrument has two output DC sources for measuring transformer winding resistance. The first DC source can output up to 2 A DC and is used for injecting current to the transformer’s high voltage winding. The second DC source can output up to 10 A DC and is used for testing the transformer’s low voltage winding. This is especially useful when measuring winding resistance of distribution transformers. These transformers have large turns ratio and therefore a big difference between resistances of high voltage and low voltage windings. Upon the winding resistance test, it is also possible to demagnetize the transformer core. The demagnetization process is completely automatic and safe.Together with the turns ratio, the instrument also measures excitation current and phase shift. This enables detecting transformer core or winding turns failures which cannot be spotted by measuring turns ratio only. The instrument can output test voltage up to 40 V AC for this test, but it can also output a very low test voltage of 1 V AC which is necessary for turns ratio verification of the majority of current transformers.TWR-H is powered by an internal Li-Ion battery. Up to 100 tests can be performed with a fully charged battery.
-
PIXXO PL-500W -
Rexus Corp.
Pixxo PL-500Watt power supply fits into a standard ATX case and will handle as many add-ons as your case can take!Pixxo is a direct manufacturer of power source solutions, producing high quality power supplies. Pixxo power supplies feature High efficiency, Low Noise and Ripple Output, Over Voltage protection and Short-circuit protection at any DC output.
-
F70PV -
FLC Electronics Inc
The F70PV is a very fast, unipolar, linear amplifier having a variable amplification of 0-10 times and capable of voltage output of +70V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
LTC3588 -
SparkFun Electronics
This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting piezoelectric energy, but solar energy as well. There is a bridge rectified input for piezo elements (PZ1 and PZ2) and a direct input (VIN) for DC sources. Both are clamped to 20V. In addition, the board can simply be used as a standalone nanopower buck regulator.
-
A10150 -
Tabor Electronics Ltd.
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
